1. How does it work?

1.1. Bridging IP over ethernet traffic between 2 LANs.

If you have:

PC1 (192.168.0.1 /24)--| PC3 (192.168.0.3 /24)--| PC5 (192.168.0.5 /24)--|--[ eth0 - bridge_1 - eth1 (195.0.0.1) ] PC253 (192.168.0.253/24)--| | (192.168.0.2 /24) PC2 | (192.168.0.4 /24) PC4 [ (192.0.0.1) eth1 - bridge_2 - eth0 ] --| (192.168.0.6 /24) PC6 | (192.168.0.254/24) PC254

bridge_1 and bridge_2 are your Linux bridges and externally connected to the Internet interface eth1. So 195.0.0.1 and 192.0.0.1 can be any valid Internet addresses given to you by your ISP.

So, you should:

1. Get two linux computers with kernels 2.2 or 2.4. Kernels should be compiled with PPP and Advanced Router. You also need the iproute2 package properly installed. Information on iproute2 can be found in Configure.help of your kernel in the comments under Advanced Router. You also need the following utilities:

   • pppd (PPP daemon) - ftp://cs.anu.edu.au/pub/software/ppp/

   • PopTop (PPTP server) - http://poptop.lineo.com

   • PPTP (Linux PPTP Client, by C.S. Ananian) - http://www.pdos.lcs.mit.edu/~cananian/Projects/PPTP/

   • tarpd (a trivial proxy arp daemon) - htp://www.cs.hut.fi/~tricky/utils/net/tarpd-1.6.tar.gz

   You can also find them on http://www.freshmeat.net

   Please, keep in mind that you need special patches for pppd and the kernel if you want to do MS Chap and MS Encryption (MPPE). Refer to the PoPTop manual for instructions on how to get and install these patches.

2. Connect your routers to Internet, or establish any other communication between them with the exception of IP.

3. Make a PPTP tunnel between them. There are example configurations in the PoPToP (server) and pptp (client) manuals.

4. Now you should have two bridges and an IP tunnel between then, possibly encrypted (refer to the PPP manual). Let's configure bridging.

5. Remember that the bridge is really a router, so we need to run the following commands on our bridges (this assumes bridge_1 and bridge_2 are IP addresses, assigned to each end of the PPTP tunnel between bridges):

   bridge_1$ip route add 192.168.0.2 via bridge_2 bridge_1$ip route add 192.168.0.4 via bridge_2 bridge_1$ip route add 192.168.0.6 via bridge_2 bridge_1$ip route add 192.168.0.254 via bridge_2 bridge_1$ip route add 192.168.0.255 via bridge_2

   On the other side:

   bridge_2$ip route add 192.168.0.1 via bridge_1 bridge_2$ip route add 192.168.0.3 via bridge_1 bridge_2$ip route add 192.168.0.5 via bridge_1 bridge_2$ip route add 192.168.0.253 via bridge_1

   This will tell each of bridges which hosts are on the other side. You can do the same with the old-style route command. It will look like:

   bridge_1$route add -host 192.168.0.2 gw bridge_2 bridge_1$route add -host 192.168.0.4 gw bridge_2 bridge_1$route add -host 192.168.0.6 gw bridge_2 bridge_1$route add -host 192.168.0.254 gw bridge_2 bridge_1$route add -host 192.168.0.255 gw bridge_2

   On the other side:

   bridge_2$route add -host 192.168.0.1 gw bridge_1 bridge_2$route add -host 192.168.0.3 gw bridge_1 bridge_2$route add -host 192.168.0.5 gw bridge_1 bridge_2$route add -host 192.168.0.253 gw bridge_1

   Please note once more that bridge_1 and bridge_2 are not IP addresses given by your ISP, but IP addresses which you assigned to each end of the PPTP tunnel.

6. Now you have two bridges and each of them knows where to find a particular IP. But how do you tell those computers to send their traffic for the remote network to the local bridge? You need tarpd.

   tarpd is a very simple daemon, which replies to arp requests for certain IP addresses. You only need to run a tarpd on each bridge, and specify the list of IP addresses found on the remote end.

   For example, for those two bridges you should run:

   bridge_1$tarpd eth0 192.168.0.2 255.255.255.255 \ 192.168.0.4 255.255.255.255 \ 192.168.0.254 255.255.255.255

   On the other side:

   bridge_2$tarpd eth0 192.168.0.1 255.255.255.255 \ 192.168.0.3 255.255.255.255 \ 192.168.0.253 255.255.255.255

   You specify 128 remote pairs (IP/mask. Mask should be 255.255.255.255 in order not to confuse tarpd!) on each bridge.

7. Enjoy your bridges!

1.2. What about other protocols?

Really, I can say nothing about other protocol routing. I never used them. But I suppose if you are familiar with other protocols, it should not be too difficult to bridge it this way.