To compile this driver into the kernel,
place the following lines in your
kernel configuration file:
device miibusdevice bce
Alternatively, to load the driver as a
module at boot time, place the following line in
loader.conf5:
if_bce_load="YES"
DESCRIPTION
The
driver supports Broadcom's NetXtreme II product family, including the
BCM5706 and BCM5708 Ethernet controllers.
The NetXtreme II product family is composed of various Converged NIC (or CNIC)
Ethernet controllers which support a TCP Offload Engine (TOE), Remote DMA (RDMA),
and iSCSI acceleration, in addition to standard L2 Ethernet traffic, all on the
same controller.
The following features are supported in the
driver under
Fx :
IP/TCP/UDP checksum offload
Jumbo frames (up to 9022 bytes)
VLAN tag stripping
Interrupt coalescing
10/100/1000Mbps operation in full-duplex mode
10/100Mbps operation in half-duplex mode
The
driver supports the following media types:
autoselect
Enable autoselection of the media type and options.
The user can manually override
the autoselected mode by adding media options to
rc.conf5.
10baseT/UTP
Set 10Mbps operation.
The
ifconfig(8)
mediaopt
option can also be used to select either
full-duplex
or
half-duplex
modes.
100baseTX
Set 100Mbps (Fast Ethernet) operation.
The
ifconfig(8)
mediaopt
option can also be used to select either
full-duplex
or
half-duplex
modes.
1000baseTX
Set 1000baseTX operation over twisted pair.
Only
full-duplex
mode is supported.
The
driver supports the following media options:
full-duplex
Force full duplex operation.
half-duplex
Force half duplex operation.
For more information on configuring this device, see
ifconfig(8).
HARDWARE
The
driver provides support for various NICs based on the Broadcom NetXtreme II
family of Gigabit Ethernet controllers, including the
following:
Broadcom NetXtreme II BCM5706 1000Base-T
Broadcom NetXtreme II BCM5706 1000Base-SX
Broadcom NetXtreme II BCM5708 1000Base-T
Broadcom NetXtreme II BCM5708 1000Base-SX
Dell PowerEdge 1950 integrated BCM5708 NIC
Dell PowerEdge 2950 integrated BCM5708 NIC
HP NC370F Multifunction Gigabit Server Adapter
HP NC370T Multifunction Gigabit Server Adapter
HP NC370i Multifunction Gigabit Server Adapter
SYSCTL VARIABLES
The following variables are available as both
sysctl(8)
variables and
loader(8)
tunables:
hw.bce.msi_enable
Whether or not MSI support is enabled in the driver.
The default value is 1.
DIAGNOSTICS
"bce%d: PCI memory allocation failed!"
The driver has encountered a fatal initialization error.
"bce%d: PCI map interrupt failed!"
The driver has encountered a fatal initialization error.
"bce%d: Unsupported controller revision (%c%d)"
The driver does not support the controller revision in use.
"bce%d: Controller initialization failed!"
The driver has encountered a fatal initialization error.
"bce%d: NVRAM test failed!"
The driver could not access the controller NVRAM correctly.
"bce%d: DMA resource allocation failed!"
The driver could not allocate DMA memory to setup the controllers
host memory data structures.
"bce%d: Interface allocation failed!"
The driver could not create a network interface for the controller.
"bce%d: PHY probe failed!"
The driver could not access the PHY used by the controller.
"bce%d: Failed to setup IRQ!"
The driver could not initialize the IRQ handler.
"bce%d: Error: PHY read timeout!"
The driver could not read a PHY register before the timeout period expired.
"bce%d: PHY write timeout!"
The driver could not write to the PHY register because a timeout occurred.
"bce%d: Timeout error reading NVRAM at offset 0x%08X!"
The driver could not write to NVRAM because a timeout occurred.
"bce%d: Unknown Flash NVRAM found!"
The driver does not recognize the NVRAM device being used and therefore
cannot access it correctly.
"bce%d: Invalid NVRAM magic value!"
The driver cannot read NVRAM or the NVRAM is corrupt.
"bce%d: Invalid Manufacturing Information NVRAM CRC!"
The driver cannot read NVRAM or the NVRAM is corrupt.
"bce%d: Invalid Feature Configuration Information NVRAM CRC!"
The driver cannot read NVRAM or the NVRAM is corrupt.
"bce%d: DMA mapping error!"
The driver was unable to map memory into DMA addressable space required
by the controller.
"bce%d: Could not allocate parent DMA tag!"
The driver could not allocate a PCI compatible DMA tag.
"bce%d: Could not allocate status block DMA tag!"
The driver could not allocate a DMA tag for the controller's
status block.
"bce%d: Could not allocate status block DMA memory!"
The driver could not allocate DMA addressable memory for the controller's
status block.
"bce_d: Could not map status block DMA memory!"
The driver could not map the status block memory into the controller's DMA
address space.
"bce%d: Could not allocate statistics block DMA tag!"
The driver could not allocate a DMA tag for the controller's
statistics block.
"bce%d: Could not allocate statistics block DMA memory!"
The driver could not allocate DMA addressable memory for the controller's
statistics block.
"bce%d: Could not map statistics block DMA memory!"
The driver could not map the statistics block memory into the controller's DMA
address space.
"bce%d: Could not allocate TX descriptor chain DMA tag!"
The driver could not allocate a DMA tag for the controller's
TX chain.
"bce%d: Could not allocate TX descriptor chain DMA memory!
The driver could not allocate DMA addressable memory for the controller's
TX chain.
"bce%d: Could not map TX descriptor chain DMA memory!"
The driver could not map the TX descriptor chain memory into the controller's DMA
address space.
"bce%d: Could not allocate TX mbuf DMA tag!"
The driver could not allocate a DMA tag for the controller's
TX mbuf memory.
"bce%d: Unable to create TX mbuf DMA map!"
The driver could not map the TX mbuf memory into the controller's DMA
address space.
"bce%d: Could not allocate RX descriptor chain DMA tag!"
The driver could not allocate a DMA tag for the controller's
RX chain.
"bce%d: Could not allocate RX descriptor chain
The driver could not allocate DMA addressable memory for the controller's
RX chain.
"bce%d: Could not map RX descriptor chain DMA memory!"
The driver could not map the RX descriptor chain memory into the controller's DMA
address space.
"bce%d: Could not allocate RX mbuf DMA tag!"
The driver could not allocate a DMA tag for the controller's
RX mbuf memory.
"bce%d: Unable to create RX mbuf DMA map!"
The driver could not map the RX mbuf memory into the controller's DMA
address space.
"bce%d: Firmware synchronization timeout!"
The driver was not able to synchronize with the firmware running on the
controller.
The firmware may be stopped or hung.
"bce%d: Invalid Ethernet address!"
The driver was not able to read a valid Ethernet MAC address from NVRAM.
"bce%d: Reset failed!"
The driver has encountered a fatal initialization error.
"bce%d: Byte swap is incorrect!"
The driver has encountered a fatal initialization error.
Contact the author
with details of the CPU architecture and system chipset in use.
"bce%d: Firmware did not complete initialization!"
The driver has encountered a fatal initialization error.
"bce%d: Bootcode not running!"
The driver has encountered a fatal initialization error.
"bce%d: Error mapping mbuf into RX chain!"
The driver could not map a RX mbuf into DMA addressable memory.
"bce%d: Error filling RX chain: rx_bd[0x%04X]!"
The driver was unable to allocate enough mbufs to fill the RX chain
during initialization.
Try increasing the number of mbufs available in
the system, increase system memory, or if using jumbo frames, make sure
enough 9KB mbufs are available.
"bce%d: Failed to allocate new mbuf, incoming frame dropped!"
The driver was unable to allocate a new mbuf for the RX chain and reused
the mbuf for the received frame, dropping the incoming frame in the process.
Try increasing the number of mbufs available in the system or increase system
memory.
"bce%d: Controller reset failed!"
A fatal initialization error has occurred.
"bce%d: Controller initialization failed!"
A fatal initialization error has occurred.
"bce%d: Block initialization failed!"
A fatal initialization error has occurred.
"bce%d: Error mapping mbuf into TX chain!"
The driver could not map a TX mbuf into DMA addressable memory.
"bce%d: Error registering poll function!"
The driver received an error while attempting to register the poll function.
"bce%d: Changing VLAN_MTU not supported."
Changing the VLAN MTU is not currently supported by the driver.
"bce%d: Cannot change VLAN_HWTAGGING while management firmware (ASF/IPMI/UMP) is running!"
Management firmware to support ASF/IPMI/UMP requires that VLAN
tag stripping be enabled in the controller.
"bce%d: Changing VLAN_HWTAGGING not supported!"
Disabling VLAN tag stripping is not currently supported by the driver.
"bce%d: Watchdog timeout occurred, resetting!"
The device has stopped responding to the network, there is a problem
with the cable connection, or a driver logic problem has occurred..
"bce%d: Fatal attention detected: 0x%08X!"
A controller hardware failure has occurred.
If the problem continues replace the controller.
