Партнёры:
Хостинг:
isic - isdn4bsd Siemens ISDN Chipset device driver
The driver supports several 8 and 16bit passive ISA, ISA PnP and PCI ISDN cards from various manufacturers which are all based upon the popular Siemens ISDN chipset consisting of the ISDN Subscriber Access Controller ISAC (such as the PEB2085 or PSB 2186) and the High-Level Serial Communications Controller Extended HSCX (such as the SAB82525 or PSB21525). The newer IPAC chip (which integrates an ISAC and a HSCX in one chip, with the added benefit of larger FIFO buffers) is also supported.
The required entry in the kernel config file is:
options TEL_S0_8
The required entry in device.hints5 file is:
hint.isic.0.at="isa" hint.isic.0.maddr="0xd0000" hint.isic.0.irq="5" hint.isic.0.flags="1"
Notice that this cards must not have a port value.
Valid values for hint.isic.N.irq are 2, 3, 4, 5, 6 and 7.
The i/o ports are memory mapped and the memory start address (hint.isic.N.maddr) may be in the range 0xA0000 to 0xDF000 and use a region of 4kB of memory.
The required entry in the kernel config file is:
options TEL_S0_16
The required entry in device.hints5 file is:
hint.isic.0.at="isa" hint.isic.0.port="0xd80" hint.isic.0.maddr="0xd0000" hint.isic.0.irq="5" hint.isic.0.flags="2"
These boards have a jumper which specifies an i/o base address (hint.isic.N.port) of either 0xd80, 0xe80 or 0xf80. The remaining necessary configuration values are then programmed at run time by accessing this i/o port.
Valid interrupts (hint.isic.N.irq) are 2, 3, 4, 5, 10, 11, 12 or 15.
Valid memory start addresses (hint.isic.N.maddr) are 0xC0000, 0xC2000, 0xC4000, 0xC6000, 0xC8000, 0xCA000, 0xCC000, 0xCE000, 0xD0000, 0xD2000, 0xD4000, 0xD6000, 0xD8000, 0xDA000, 0xDC000 and 0xDE000.
Notice: Although the jumpers are labeled 0xd80, 0xe80 or 0xf80, they also require i/o space at addresses 0x180, 0x280 or 0x380.
The required entry in the kernel config file is:
options TEL_S0_16_3
The required entry in device.hints5 file is:
hint.isic.0.at="isa" hint.isic.0.port="0xd80" hint.isic.0.irq="5" hint.isic.0.flags="3"
This card is completely i/o mapped and must not have an maddr statement in the hints file.
Valid interrupts (hint.isic.N.irq) are 2, 5, 9, 10, 12 or 15.
These boards have a jumper which specifies an i/o base address (hint.isic.N.port) of either 0xd80, 0xe80 or 0xf80.
Notice: Although the switch positions are labeled 0x180, 0x280 and 0x380, the card is to be configured at 0xd80, 0xe80 or 0xf80 respectively!
The required entry in the kernel config file is:
options AVM_A1
The required entry in device.hints5 file is:
hint.isic.0.at="isa" hint.isic.0.port="0x340" hint.isic.0.irq="5" hint.isic.0.flags="4"
These boards have a jumper which specifies an i/o base address (hint.isic.N.port) of either 0x200, 0x240, 0x300 or 0x340.
Valid interrupt (hint.isic.N.irq) values are 3, 4, 5, 6, 7, 10, 11, 12 or 15.
Older Versions of the AVM A1 also require setting of an IRQ jumper, newer versions of this and the Fritz!Card only have an i/o base jumper and the interrupt is setup at runtime by reprogramming a register.
The required entry in the kernel config file is:
options USR_STI
The required entry in device.hints5 file is:
hint.isic.0.at="isa" hint.isic.0.port="0x268" hint.isic.0.irq="5" hint.isic.0.flags="7"
Valid i/o port values (hint.isic.N.port) are 0x200, 0x208, 0x210, 0x218, 0x220, 0x228, 0x230, 0x238, 0x240, 0x248, 0x250, 0x258, 0x260, 0x268, 0x270 and 0x278.
Valid interrupt (hint.isic.N.irq) values are 5, 7, 10, 11, 12, 14, 15.
Notice: this card has a strange address decoding scheme resulting in occupying 64 windows of some bytes length over the whole i/o address range.
The required entry in the kernel config file is:
options ITKIX1
The required entry in device.hints5 file is:
hint.isic.0.at="isa" hint.isic.0.port="0x398" hint.isic.0.irq="10" hint.isic.0.flags="18"
Valid i/o port values must be in the range (<unknown>).
Valid interrupt configurations are (<unknown>).
The required entry in the kernel config file is:
options ELSA_PCC16
The required entry in device.hints5 file is:
hint.isic.0.at="isa" hint.isic.0.port="0x360" hint.isic.0.irq="10" hint.isic.0.flags="20"
Valid i/o port (hint.isic.N.port) values are 0x160, 0x170, 0x260 and 0x360.
Valid interrupt (hint.isic.N.irq) values are 2, 3, 5, 10, 11 and 15.
The LED's are not supported and are off.
The required entry in the kernel config file is:
options TEL_S0_16_3_P
The required entry in the kernel config file is:
options CRTX_S0_P
The required entry in the kernel config file is:
options DRN_NGO
The required entry in the kernel config file is:
options SEDLBAUER
The required entry in the kernel config file is:
options DYNALINK
The required entry in the kernel config file is:
options ELSA_QS1ISA
The LED's are not supported and are off.
The required entry in the kernel config file is:
options SIEMENS_ISURF2
The required entry in the kernel config file is:
options ASUSCOM_IPAC
The required entry in the kernel config file is:
options EICON_DIVA
The required entry in the kernel config file is:
options COMPAQ_M610
The required entry in the kernel config file is:
options ELSA_QS1PCI
The LED's are not supported and are off.
|
Закладки на сайте Проследить за страницей |
Created 1996-2024 by Maxim Chirkov Добавить, Поддержать, Вебмастеру |