[ новости /+++ | форум | теги | ]

NAME
     xd, xdc - disk driver for Xylogics 7053 SMD Disk Controller

SYNOPSIS
     xdc@6d,ee80/xd@slave,0:partition

     xdc@6d,ee90/xd@slave,0:partition

     xdc@6d,eea0/xd@slave,0:partition

     xdc@6d,eeb0/xd@slave,0:partition

DESCRIPTION
     The driver for Xylogics 7053  devices  consists  of  several
     components:  a  controller  driver  (xdc) and a slave device
     driver module (xd). Each driver  module  has  an  associated
     configuration file, which lives in the same directory as the
     driver module. See driver.conf(4) and for the interpretation
     of the contents of these files.

     The block files access the disk using  the  system's  normal
     buffering  mechanism  and  may  be  read and written without
     regard to physical disk  records.   There  is  also  a   raw
     interface  that provides for direct transmission between the
     disk and the user's read or write buffer. A single  read  or
     write call usually results in only one I/O operation; there-
     fore raw I/O is considerably more efficient when many  words
     are transmitted. The physical names of the raw files conven-
     tionally have `,raw' appended to them. The logical names for
     the raw files live in the /dev/rdsk directory, as usual.

     When using raw I/O, transfer counts should be  multiples  of
     512  bytes (the size of a disk sector). Likewise, when using
     lseek(2) to specify block offsets from which to perform  raw
     I/O,  the  logical  offset  should also be a multiple of 512
     bytes.

     Partition 0 is normally used for the root file system  on  a
     disk,  partition 1 as a paging area (for example, swap), and
     partition 2 for backing up the entire disk. Partition 2 nor-
     mally maps the entire disk and may also be used as the mount
     point for secondary disks in the system.  The  rest  of  the
     disk is normally partition 6. For the primary disk, the user
     file system is located here.

DISK SUPPORT
     This driver handles all SMD drives by reading a  label  from
     sector  0 of the drive which describes the disk geometry and
     partitioning.

FILES
     /kernel/drv/xdc
           driver module

     /kernel/drv/xd
           driver module

     /kernel/drv/xdc.conf
           driver configuration file

     /kernel/drv/xd.conf
           driver configuration file

     /dev/dsk/cXdYsZ
           block devices, controller X, unit Y, slice Z

     /dev/rdsk/cXdYsZ
           raw devices, controller X, unit Y, slice Z

ATTRIBUTES
     See attributes(5) for descriptions of the  following  attri-
     butes:

     ____________________________________________________________
   |        ATTRIBUTE TYPE       |        ATTRIBUTE VALUE      |
   | ____________________________|_____________________________|_
   |  Architecture               |  SPARC   (Sun-4/200,    Sun-|
   |                             |  4/300, and Sun-4/400 series|
   |                             |  only)                      |
   |_____________________________|_____________________________|


SEE ALSO
     lseek(2), read(2), write(2), driver.conf(4),  attributes(5),
     dkio(7I), hdio(7I)

NOTES
     In raw I/O read(2) and write(2)  truncate  file  offsets  to
     512-byte  block  boundaries,  and  write(2) scribbles on the
     tail of incomplete blocks. Thus, in programs that are likely
     to  access  raw  devices,  read(2),  write(2),  and lseek(2)
     should always deal in 512-byte multiples.

Партнёры:

Хостинг: