The
utility and the console driver work together to support
mouse operation in the text console and user programs.
They virtualize the mouse and provide user programs with mouse data
in the standard format
(see
sysmouse(4)).
The mouse daemon listens to the specified port for mouse data,
interprets and then passes it via ioctls to the console driver.
The mouse daemon
reports translation movement, button press/release
events and movement of the roller or the wheel if available.
The roller/wheel movement is reported as
``Z''
axis movement.
The console driver will display the mouse pointer on the screen
and provide cut and paste functions if the mouse pointer is enabled
in the virtual console via
vidcontrol(1).
If
sysmouse(4)
is opened by the user program, the console driver also passes the mouse
data to the device so that the user program will see it.
If the mouse daemon receives the signal
SIGHUP
it will reopen the mouse port and reinitialize itself.
Useful if
the mouse is attached/detached while the system is suspended.
If the mouse daemon receives the signal
SIGUSR1
it will stop passing mouse events.
Sending the signal
SIGUSR1
again will resume passing mouse events.
Useful if your typing on a laptop is
interrupted by accidentally touching the mouse pad.
The following options are available:
-3
Emulate the third (middle) button for 2-button mice.
It is emulated
by pressing the left and right physical buttons simultaneously.
-C threshold
Set double click speed as the maximum interval in msec between button clicks.
Without this option, the default value of 500 msec will be assumed.
This option will have effect only on the cut and paste operations
in the text mode console.
The user program which is reading mouse data
via
sysmouse(4)
will not be affected.
-D
Lower DTR on the serial port.
This option is valid only if
mousesystems
is selected as the protocol type.
The DTR line may need to be dropped for a 3-button mouse
to operate in the
mousesystems
mode.
-E timeout
When the third button emulation is enabled
(see above),
the
utility waits
timeout
msec at most before deciding whether two buttons are being pressed
simultaneously.
The default timeout is 100 msec.
-F rate
Set the report rate (reports/sec) of the device if supported.
-L distance
When
``Virtual Scrolling''
is enabled, the
-L
option can be used to set the
distance
(in pixels) that the mouse must move before a scroll event
is generated. This effectively controls the scrolling speed.
The default
distance
is 2 pixels.
-H
Enable
``Horizontal Virtual Scrolling''
With this option set, holding the middle mouse
button down will cause motion to be interpreted as
horizontal scrolling.
Use the
-U
option to set the distance the mouse must move before the scrolling mode is
activated and the
-L
option to set the scrolling speed.
This option may be used with or without the
-V
option.
-I file
Write the process id of the
utility in the specified file.
Without this option, the process id will be stored in
/var/run/moused.pid
-P
Do not start the Plug and Play COM device enumeration procedure
when identifying the serial mouse.
If this option is given together with the
-i
option, the
utility will not be able to print useful information for the serial mouse.
-R
Lower RTS on the serial port.
This option is valid only if
mousesystems
is selected as the protocol type by the
-t
option below.
It is often used with the
-D
option above.
Both RTS and DTR lines may need to be dropped for
a 3-button mouse to operate in the
mousesystems
mode.
-S baudrate
Select the baudrate for the serial port (1200 to 9600).
Not all serial mice support this option.
-T distance [, time [, after
]
]
Terminate drift.
Use this option if mouse pointer slowly wanders when mouse is not moved.
Movements up to
distance
(for example 4) pixels (X+Y) in
time
msec (default 500) are ignored, except during
after
msec (default 4000) since last real mouse movement.
-V
Enable
``Virtual Scrolling''
With this option set, holding the middle mouse
button down will cause motion to be interpreted as scrolling.
Use the
-U
option to set the distance the mouse must move before the scrolling mode is
activated and the
-L
option to set the scrolling speed.
-U distance
When
``Virtual Scrolling''
is enabled, the
-U
option can be used to set the
distance
(in pixels) that the mouse must move before the scrolling
mode is activated.
The default
distance
is 3 pixels.
-A exp [, offset
]
Apply exponential (dynamic) acceleration to mouse movements:
the faster you move the mouse, the more it will be accelerated.
That means that small mouse movements are not accelerated,
so they are still very accurate, while a faster movement will
drive the pointer quickly across the screen.
The
exp
value specifies the exponent, which is basically
the amount of acceleration. Useful values are in the
range 1.1 to 2.0, but it depends on your mouse hardware
and your personal preference. A value of 1.0 means no
exponential acceleration. A value of 2.0 means squared
acceleration (i.e. if you move the mouse twice as fast,
the pointer will move four times as fast on the screen).
Values beyond 2.0 are possible but not recommended.
A good value to start is probably 1.5.
The optional
offset
value specifies the distance at which the acceleration
begins. The default is 1.0, which means that the
acceleration is applied to movements larger than one unit.
If you specify a larger value, it takes more speed for
the acceleration to kick in, i.e. the speed range for
small and accurate movements is wider.
Usually the default should be sufficient, but if you're
not satisfied with the behaviour, try a value of 2.0.
Note that the
-A
option interacts badly with the X server's own acceleration,
which doesn't work very well anyway. Therefore it is
recommended to switch it off if necessary:
``xset m 1''
-a X [, Y
]
Accelerate or decelerate the mouse input.
This is a linear acceleration only.
Values less than 1.0 slow down movement, values greater than 1.0 speed it
up.
Specifying only one value sets the acceleration for both axes.
You can use the
-a
and
-A
options at the same time to have the combined effect
of linear and exponential acceleration.
-c
Some mice report middle button down events
as if the left and right buttons are being pressed.
This option handles this.
-d
Enable debugging messages.
-f
Do not become a daemon and instead run as a foreground process.
Useful for testing and debugging.
-i info
Print specified information and quit.
Available pieces of
information are:
port
Port (device file) name, i.e.
/dev/cuad0
/dev/mse0
and
/dev/psm0
if
Interface type: serial, bus, inport or ps/2.
type
Protocol type.
It is one of the types listed under the
-t
option below or
sysmouse
if the driver supports the
sysmouse
data format standard.
model
Mouse model.
The
utility may not always be able to identify the model.
all
All of the above items.
Print port, interface, type and model in this order
in one line.
If the
utility cannot determine the requested information, it prints
``unknown
''
or
``generic
''
-l level
Specifies at which level
should operate the mouse driver.
Refer to
Sx Operation Levels
in
psm(4)
for more information on this.
-m N=M
Assign the physical button
M
to the logical button
N
You may specify as many instances of this option as you like.
More than one physical button may be assigned to a logical button at the
same time.
In this case the logical button will be down,
if either of the assigned physical buttons is held down.
Do not put space around
`='
-p port
Use
port
to communicate with the mouse.
-r resolution
Set the resolution of the device; in Dots Per Inch, or
lowmedium-lowmedium-high
or
high
This option may not be supported by all the device.
-s
Select a baudrate of 9600 for the serial line.
Not all serial mice support this option.
-t type
Specify the protocol type of the mouse attached to the port.
You may explicitly specify a type listed below, or use
auto
to let the
utility automatically select an appropriate protocol for the given
mouse.
If you entirely omit this option in the command line,
-t auto
is assumed.
Under normal circumstances,
you need to use this option only if the
utility is not able to detect the protocol automatically
(see
Sx Configuring Mouse Daemon ) .
Note that if a protocol type is specified with this option, the
-P
option above is implied and Plug and Play COM device enumeration
procedure will be disabled.
Also note that if your mouse is attached to the PS/2 mouse port, you should
always choose
auto
or
ps/2
regardless of the brand and model of the mouse.
Likewise, if your
mouse is attached to the bus mouse port, choose
auto
or
busmouse
Serial mouse protocols will not work with these mice.
For the USB mouse, the protocol must be
auto
No other protocol will work with the USB mouse.
Valid types for this option are
listed below.
For the serial mouse:
microsoft
Microsoft serial mouse protocol.
Most 2-button serial mice use this protocol.
intellimouse
Microsoft IntelliMouse protocol.
Genius NetMouse,
ASCII
Mie Mouse,
Logitech MouseMan+ and FirstMouse+ use this protocol too.
Other mice with a roller/wheel may be compatible with this protocol.
mousesystems
MouseSystems 5-byte protocol.
3-button mice may use this protocol.
mmseries
MM Series mouse protocol.
logitech
Logitech mouse protocol.
Note that this is for old Logitech models.
mouseman
or
intellimouse
should be specified for newer models.
mouseman
Logitech MouseMan and TrackMan protocol.
Some 3-button mice may be compatible
with this protocol.
Note that MouseMan+ and FirstMouse+ use
intellimouse
protocol rather than this one.
glidepoint
ALPS GlidePoint protocol.
thinkingmouse
Kensington ThinkingMouse protocol.
mmhitab
Hitachi tablet protocol.
x10mouseremote
X10 MouseRemote.
kidspad
Genius Kidspad and Easypad protocol.
versapad
Interlink VersaPad protocol.
gtco_digipad
GTCO Digipad protocol.
For the bus and InPort mouse:
busmouse
This is the only protocol type available for
the bus and InPort mouse and should be specified for any bus mice
and InPort mice, regardless of the brand.
For the PS/2 mouse:
ps/2
This is the only protocol type available for the PS/2 mouse
and should be specified for any PS/2 mice, regardless of the brand.
For the USB mouse,
auto
is the only protocol type available for the USB mouse
and should be specified for any USB mice, regardless of the brand.
-w N
Make the physical button
N
act as the wheel mode button.
While this button is pressed, X and Y axis movement is reported to be zero
and the Y axis movement is mapped to Z axis.
You may further map the Z axis movement to virtual buttons by the
-z
option below.
-z target
Map Z axis (roller/wheel) movement to another axis or to virtual buttons.
Valid
target
maybe:
x
y
X or Y axis movement will be reported when the Z axis movement is detected.
N
Report down events for the virtual buttons
N
and
N+1
respectively when negative and positive Z axis movement
is detected.
There do not need to be physical buttons
N
and
N+1
Note that mapping to logical buttons is carried out after mapping
from the Z axis movement to the virtual buttons is done.
N1 N2
Report down events for the virtual buttons
N1
and
N2
respectively when negative and positive Z axis movement
is detected.
N1 N2 N3 N4
This is useful for the mouse with two wheels of which
the second wheel is used to generate horizontal scroll action,
and for the mouse which has a knob or a stick which can detect
the horizontal force applied by the user.
The motion of the second wheel will be mapped to the buttons
N3
for the negative direction, and
N4
for the positive direction.
If the buttons
N3
and
N4
actually exist in this mouse, their actions will not be detected.
Note that horizontal movement or second roller/wheel movement may not
always be detected,
because there appears to be no accepted standard as to how it is encoded.
Note also that some mice think left is the negative horizontal direction;
others may think otherwise.
Moreover, there are some mice whose two wheels are both mounted vertically,
and the direction of the second vertical wheel does not match the
first one.
Configuring Mouse Daemon
The first thing you need to know is the interface type
of the mouse you are going to use.
It can be determined by looking at the connector of the mouse.
The serial mouse has a D-Sub female 9- or 25-pin connector.
The bus and InPort mice have either a D-Sub male 9-pin connector
or a round DIN 9-pin connector.
The PS/2 mouse is equipped with a small, round DIN 6-pin connector.
Some mice come with adapters with which the connector can
be converted to another.
If you are to use such an adapter,
remember the connector at the very end of the mouse/adapter pair is
what matters.
The USB mouse has a flat rectangular connector.
The next thing to decide is a port to use for the given interface.
For the bus, InPort and PS/2 mice, there is little choice:
the bus and InPort mice always use
/dev/mse0
and the PS/2 mouse is always at
/dev/psm0
There may be more than one serial port to which the serial
mouse can be attached.
Many people often assign the first, built-in
serial port
/dev/cuad0
to the mouse.
You can attach multiple USB mice to your system or to your USB hub.
They are accessible as
/dev/ums0 , /dev/ums1
and so on.
You may want to create a symbolic link
/dev/mouse
pointing to the real port to which the mouse is connected, so that you
can easily distinguish which is your
``mouse''
port later.
The next step is to guess the appropriate protocol type for the mouse.
The
utility may be able to automatically determine the protocol type.
Run the
utility with the
-i
option and see what it says.
If the command can identify
the protocol type, no further investigation is necessary on your part.
You may start the daemon without explicitly specifying a protocol type
(see
Sx EXAMPLES ) .
The command may print
sysmouse
if the mouse driver supports this protocol type.
Note that the
type
and
model
printed by the
-i
option do not necessarily match the product name of the pointing device
in question, but they may give the name of the device with which it is
compatible.
If the
-i
option yields nothing, you need to specify a protocol type to the
utility by the
-t
option.
You have to make a guess and try.
There is rule of thumb:
The bus and InPort mice always use
busmouse
protocol regardless of the brand of the mouse.
The
ps/2
protocol should always be specified for the PS/2 mouse
regardless of the brand of the mouse.
You must specify the
auto
protocol for the USB mouse.
Most 2-button serial mice support the
microsoft
protocol.
3-button serial mice may work with the
mousesystems
protocol.
If it does not, it may work with the
microsoft
protocol although
the third (middle) button will not function.
3-button serial mice may also work with the
mouseman
protocol under which the third button may function as expected.
3-button serial mice may have a small switch to choose between
``MS''
and
``PC''
or
``2''
and
``3''
``MS''
or
``2''
usually mean the
microsoft
protocol.
``PC''
or
``3''
will choose the
mousesystems
protocol.
If the mouse has a roller or a wheel, it may be compatible with the
intellimouse
protocol.
To test if the selected protocol type is correct for the given mouse,
enable the mouse pointer in the current virtual console,
and see if the mouse pointer travels correctly
according to the mouse movement.
Then try cut & paste features by
clicking the left, right and middle buttons.
Type ^C to stop
the command.
Multiple Mice
As many instances of the mouse daemon as the number of mice attached to
the system may be run simultaneously; one
instance for each mouse.
This is useful if the user wants to use the built-in PS/2 pointing device
of a laptop computer while on the road, but wants to use a serial
mouse when s/he attaches the system to the docking station in the office.
Run two mouse daemons and tell the application program
(such as the
X Window System
to use
sysmouse(4),
then the application program will always see mouse data from either mouse.
When the serial mouse is not attached, the corresponding mouse daemon
will not detect any movement or button state change and the application
program will only see mouse data coming from the daemon for the
PS/2 mouse.
In contrast when both mice are attached and both of them
are moved at the same time in this configuration,
the mouse pointer will travel across the screen just as if movement of
the mice is combined all together.
FILES
/dev/consolectl
device to control the console
/dev/mse%d
bus and InPort mouse driver
/dev/psm%d
PS/2 mouse driver
/dev/sysmouse
virtualized mouse driver
/dev/ttyv%d
virtual consoles
/dev/ums%d
USB mouse driver
/var/run/moused.pid
process id of the currently running
utility
/var/run/MouseRemote
UNIX-domain stream socket for X10 MouseRemote events
EXAMPLES
"moused -p /dev/cuad0 -i type"
Let the
utility determine the protocol type of the mouse at the serial port
/dev/cuad0
If successful, the command will print the type, otherwise it will say
``unknown
''
moused -p /dev/cuad0
vidcontrol -m on
If the
utility is able to identify the protocol type of the mouse at the specified
port automatically, you can start the daemon without the
-t
option and enable the mouse pointer in the text console as above.
moused -p /dev/mouse -t microsoft
vidcontrol -m on
Start the mouse daemon on the serial port
/dev/mouse
The protocol type
microsoft
is explicitly specified by the
-t
option.
"moused -p /dev/mouse -m 1=3 -m 3=1"
Assign the physical button 3 (right button) to the logical button 1
(logical left) and the physical button 1 (left) to the logical
button 3 (logical right).
This will effectively swap the left and right buttons.
"moused -p /dev/mouse -t intellimouse -z 4"
Report negative Z axis movement (i.e., mouse wheel) as the button 4 pressed
and positive Z axis movement (i.e., mouse wheel) as the button 5 pressed.
If you add
"ALL ALL = NOPASSWD: /usr/bin/killall -USR1 moused"
to your
/usr/local/etc/sudoers
file, and bind
"killall -USR1 moused"
to a key in your window manager, you can suspend mouse events on your laptop if
you keep brushing over the mouse pad while typing.
CAVEATS
Many pad devices behave as if the first (left) button were pressed if
the user
``taps''
the surface of the pad.
In contrast, some ALPS GlidePoint and Interlink VersaPad models
treat the tapping action
as fourth button events.
Use the option
``-m 1=4
''
for these models
to obtain the same effect as the other pad devices.
Cut and paste functions in the virtual console assume that there
are three buttons on the mouse.
The logical button 1 (logical left) selects a region of text in the
console and copies it to the cut buffer.
The logical button 3 (logical right) extends the selected region.
The logical button 2 (logical middle) pastes the selected text
at the text cursor position.
If the mouse has only two buttons, the middle, `paste' button
is not available.
To obtain the paste function, use the
-3
option to emulate the middle button, or use the
-m
option to assign the physical right button to the logical middle button:
``-m 2=3
''
The
utility partially supports
``Plug and Play External COM Device Specification''
in order to support PnP serial mice.
However, due to various degrees of conformance to the specification by
existing serial mice, it does not strictly follow the version 1.0 of the
standard.
Even with this less strict approach,
it may not always determine an appropriate protocol type
for the given serial mouse.
HISTORY
The
utility first appeared in
Fx 2.2 .
AUTHORS
An -nosplit
The
utility was written by
An Michael Smith Aq msmith@FreeBSD.org .
This manual page was written by
An Mike Pritchard Aq mpp@FreeBSD.org .
The command and manual page have since been updated by
An Kazutaka Yokota Aq yokota@FreeBSD.org .
