Интерактивная система просмотра системных руководств (man-ов)
rshd (8)
rshd (8) ( FreeBSD man: Команды системного администрирования )
>> rshd (8) ( Linux man: Команды системного администрирования )
BSD mandoc
Linux NetKit (0.17)
NAME
rshd
- remote shell server
SYNOPSIS
rshd
[-ahlnL
]
DESCRIPTION
The
rshd
server
is the server for the
rcmd(3)
routine and, consequently, for the
rsh(1)
program. The server provides remote execution facilities
with authentication based on privileged port numbers from trusted hosts.
The
rshd
server
listens for service requests at the port indicated in
the ``cmd'' service specification; see
services(5).
When a service request is received the following protocol
is initiated:
The server checks the client's source port.
If the port is not in the range 512-1023, the server
aborts the connection.
The server reads characters from the socket up
to a null (`\0') byte. The resultant string is
interpreted as an
ASCII
number, base 10.
If the number received in step 2 is non-zero,
it is interpreted as the port number of a secondary
stream to be used for the
stderr
A second connection is then created to the specified
port on the client's machine. The source port of this
second connection is also in the range 512-1023.
The server checks the client's source address
and requests the corresponding host name (see
gethostbyaddr(3),
hosts(5)
and
named(8)).
If the hostname cannot be determined,
the dot-notation representation of the host address is used.
If the hostname is in the same domain as the server (according to
the last two components of the domain name),
or if the
-a
option is given,
the addresses for the hostname are requested,
verifying that the name and address correspond.
If address verification fails, the connection is aborted
with the message, ``Host address mismatch.''
A null terminated user name of at most 16 characters
is retrieved on the initial socket. This user name
is interpreted as the user identity on the
client 's
machine.
A null terminated user name of at most 16 characters
is retrieved on the initial socket. This user name
is interpreted as a user identity to use on the
server 's
machine.
A null terminated command to be passed to a
shell is retrieved on the initial socket. The length of
the command is limited by the upper bound on the size of
the system's argument list.
Rshd
then validates the user using
ruserok(3),
which uses the file
/etc/hosts.equiv
and the
.rhosts
file found in the user's home directory. The
-l
option prevents
ruserok(3)
from doing any validation based on the user's ``.rhosts'' file
(unless the user is the superuser and the
-h
option is used.) If the
-h
option is not used, superuser accounts may not be accessed via this
service at all.
The
-l
option should not be trusted without verifying that it works as
expected with the particular version of libc installed on your system
(and should be tested again after any libc update) because some
versions of libc may not honor the flags used by
rshd
Also note that the design of the
.rhosts
system is COMPLETELY INSECURE except on a carefully firewalled private
network. Under all other circumstances,
rshd
should be disabled entirely.
A null byte is returned on the initial socket
and the command line is passed to the normal login
shell of the user. The
shell inherits the network connections established
by
rshd
Transport-level keepalive messages are enabled unless the
-n
option is present.
The use of keepalive messages allows sessions to be timed out
if the client crashes or becomes unreachable.
The
-L
option causes all successful accesses to be logged to
syslogd(8)
as
auth.info
messages and all failed accesses to be logged as
auth.notice
DIAGNOSTICS
Except for the last one listed below,
all diagnostic messages
are returned on the initial socket,
after which any network connections are closed.
An error is indicated by a leading byte with a value of
1 (0 is returned in step 9 above upon successful completion
of all the steps prior to the execution of the login shell).
Locuser too long.
The name of the user on the client's machine is
longer than 16 characters.
Ruser too long.
The name of the user on the remote machine is
longer than 16 characters.
Command too long
The command line passed exceeds the size of the argument
list (as configured into the system).
Remote directory.
The
chdir
command to the home directory failed.
Permission denied.
The authentication procedure described above failed, or the user
requested did not exist. (These conditions are intentionally conflated.)
Can't make pipe.
The pipe needed for the
stderr
wasn't created.
Can't fork; try again.
A
fork
by the server failed.
<shellname>: ...
The user's login shell could not be started. This message is returned
on the connection associated with the
stderr
and is not preceded by a flag byte.
The authentication procedure used here assumes the integrity
of each client machine and the connecting medium. This is
insecure, but is useful in an ``open'' environment.
A facility to allow all data exchanges to be encrypted should be
present.
A more extensible protocol (such as Telnet) should be used.
