[ новости /+++ | форум | теги | ]

NAME

scsi_id - retrieve and generate a unique SCSI identifier
 

SYNOPSIS

DESCRIPTION

If a result is generated it is sent to standard output, and the program exits with a zero value. If no identifier is output, the program exits with a non-zero value.

scsi_id is primarily for use by other utilities such as udev that require a unique SCSI identifier.

By default all devices are assume black listed, the -g option must be specified on the command line or in the config file for any useful behaviour.

SCSI commands are sent directly to the device via the SG_IO ioctl interface.

In order to generate unique values for either page 0x80 or page 0x83, the serial numbers or world wide names are prefixed as follows.

Identifiers based on page 0x80 are prefixed by the character 'S', the SCSI vendor, the SCSI product (model) and then the the serial number returned by page 0x80. For example:

# scsi_id -p 0x80 -s /block/sdg
SIBM     3542           1T05078453

Identifiers based on page 0x83 are prefixed by the identifier type followed by the page 0x83 identifier. For example, a device with a NAA (Name Address Authority) type of 3 (also in this case the page 0x83 identifier starts with the NAA value of 6):

# /sbin/scsi_id -p 0x83 -s /block/sdg
3600a0b80000b174b000000d63efc5c8c

OPTIONS

subsystem

Deprecated method: when called with only a single argument without a leading -, runs in a hotplug mode, and expects the environment variable DEVPATH to specify the corresponding sysfs device. See section below on usage with udev.

-a

Always print information (model, vendor strings) about the device even if it does not support VPD pages.

-b

The default behaviour - treat the device as black listed, and do nothing unless a white listed device is found in the scsi_id config-file.

-d device

Instead of determining and creating a device node based on a sysfs dev entry as done for the -s, send SG_IO commands to device, such as /dev/sdc. This argument should also be used when invoked via udev to avoid problems with creation of temporary files on not-yet writable directories.

-f config-file

Read configuration and black/white list entries from config-file rather than the default /etc/scsi_id.config file.

-g

Treat the device as white listed. The -g option must be specified on the command line or in the scsi_id configuration file for scsi_id to generate any output.

-i

Prefix the identification string with the driver model (sysfs) bus id of the SCSI device.

-p 0x80 | 0x83 | pre-spc3-83

Use SCSI INQUIRY VPD page code 0x80, 0x83, or pre-spc3-83.

The default behaviour is to query the availabe VPD pages, and use page 0x83 if found, else page 0x80 if found, else nothing.

Page pre-spc3-83 should only be utilized for those scsi devices which are not compliant with the SPC-2 or SPC-3 format for page 83. While this option is used for older model 4, 5, and 6 EMC Symmetrix devices, its use with SPC-2 or SPC-3 compliant devices will fallback to the page 83 format supported by these devices.

-s sysfs-device

Generate an id for the sysfs-device. The sysfs mount point must not be included. For example, use /block/sd, not /sys/block/sd.

-u

Reformat the output : replace all whitespaces by underscores.

-x

Export all data in KEY=<value> format used to import in other programs.

-v

Generate verbose debugging output.

-V

Display version number and exit.

USAGE WITH UDEV

If scsi_id is invoked with one argument without a leading -, it assumes it is called for a hotplug event, and looks for the sysfs device in the DEVPATH environment variable. This mode is deprecated, but available for backwards compatibility.

If the DEVPATH environment variable is set, scsi_id assumes it has been invoked via udev (or some other hotplug program), and all errors or warnings are sent using syslog.

To determine the specific value needed in a RESULT key, use the -s option, for example:

/sbin/scsi_id -s /block/sda

scsi_id is one of the tools used in the "Linux Persistent Device Names" scheme that creates persistent device links in /dev/disk. It is called with the -x option which will print all values in a defined format to let udev import it into its own environment for later event processing.

An example custom udev rule using scsi_id, that will name a block device and any partitions for the device matching the scsi_id output of 312345:

BUS=="scsi", PROGRAM=="/sbin/scsi_id -d %N -s %p", RESULT=="312345", NAME="disk%n"

FILES

/etc/scsi_id.config                  configuration and black/white list entries

SEE ALSO

AUTHORS

Index

NAME

SYNOPSIS

DESCRIPTION

OPTIONS

USAGE WITH UDEV

FILES

SEE ALSO

AUTHORS

Партнёры:

Хостинг: